A barcode label that works fine on a dry shelf can curl, peel or smear the first week it goes into a freezer, a wet loading dock or a yard. Often the barcode itself is fine. The label material, the adhesive or the print method gave out.

This guide covers what to look for when labels face cold, moisture, sunlight or chemicals, and how to test before you buy a thousand of them. For how each printer type works, see direct thermal vs. thermal transfer vs. sheet labels. This is general information; the datasheet for the exact label and adhesive you buy has the final word.

What fails, and why

Four things usually go wrong, and each has a different fix:

  • The adhesive never bonds. Adhesives need warmth to grab. Most pressure-sensitive adhesives take longer to bond in the cold (Refrigerated & Frozen Foods), so a label stuck onto a frosty box may look attached and then fall off.
  • Moisture lifts the edges. Temperature changes, such as a grocery item moving from a cold refrigerator to a warm car, can cause condensation, which the article says can make labels lift at the edges or fall off. Water on the surface is also a contaminant that weakens the bond.
  • The facestock degrades. Zebra rates uncoated paper as having limited resistance to moisture or abrasion, and a label supplier says polypropylene resists moisture and decay better.
  • The surface changes. Frost, oil, curved containers and rough corrugate all need an adhesive chosen for them.

Start with the print method

For anything that will see weather, chemicals or a long service life, choose thermal transfer. Zebra's selector guide rates direct thermal as primarily indoor with minimal chemical resistance, and thermal transfer as indoor or outdoor with excellent chemical resistance (the printer comparison has the full table).

Direct thermal can still work for a short job, such as a label that is printed, applied and shipped within days. Zebra's catalog rates a basic uncoated direct thermal paper label as not recommended for outdoor use. If a label must last a season, plan on thermal transfer.

Match the facestock to the conditions

The facestock is the label's top layer. A supplier's freezer guide lists the broad pattern: paper for dry conditions, polyester for wet conditions, polypropylene for added moisture resistance, and vinyl as the most durable and most expensive (Smith Corona). Zebra's catalog gives some concrete examples:

FacestockWhat Zebra's catalog saysTypical fit
Uncoated paperLimited resistance to moisture or abrasionDry, indoor, short-term
PolyolefinRecommended for up to 6 months outdoorsCurved or rough surfaces
PolypropyleneThermal transfer versions recommended for up to 1 to 2 years outdoorsMoisture, cold chain, drums
Matte polyesterRecommended for up to 2 years outdoors; one Zebra matte polyester is rated excellent for chemicals, others moderate or harsh, so check the itemEquipment, asset and rating labels

Those outdoor durations are Zebra's recommendations for specific products, not guarantees. Direct sun, salt air, pressure washing and abrasion shorten them. Pair synthetic labels with the ribbon the manufacturer lists for them; Zebra pairs gloss synthetics with resin ribbons.

Read two temperatures on the adhesive

Every adhesive has two separate temperature figures, and mixing them up causes most freezer failures:

  • Minimum application temperature is the lowest temperature at which you can stick the label on and expect it to bond.
  • Service temperature range is the range the label tolerates once it is stuck.

Compare two Zebra paper thermal transfer labels. Zebra's Z-Select 4000T general-purpose label is applied at 25°F or warmer. An all-temp version can be applied to surfaces as cold as -20°F (-29°C) and carries a service range of -65°F to 200°F. Zebra describes the all-temp type for identifying products in cold storage. If you must label inside a freezer, you want a number like the second one.

Zebra's adhesive list also includes a cold-temperature type rated to hold at temperatures down to -112°F (-80°C), and a wet-tack type for wet surfaces. If your labels go on damp or frosty items, ask the supplier whether the adhesive you are considering is rated for that.

Apply labels so they actually stick

How you put the label on matters as much as what it is made of:

  1. Label at room temperature when you can. Room temperature gives the adhesive its best initial tack, and a supplier advises letting it set before the item goes into the freezer (Smith Corona). Some adhesives wet out almost instantly while others can take up to 30 minutes, so ask which kind you have.
  2. Wipe the surface dry and frost-free. Frost is a layer of ice between the label and the package, not a surface.
  3. Press firmly across the whole label, especially the edges and corners.
  4. Avoid abrupt moves. Sudden temperature changes and blower airflow can dislodge a label that has not fully set (Smith Corona).
  5. Round the corners and keep the barcode away from edges and folds, where a lifting corner starts. The placement guide covers flat and curved spots on packaging.

Test before you roll out

One label supplier suggests requesting a sample roll and testing it in your actual environment before you buy (Smith Corona). An adhesive article points to initial tack, peel strength and shear resistance as the properties to evaluate and advises working closely with the adhesive supplier when choosing (Refrigerated & Frozen Foods). You can do a practical version of that without a lab:

  1. Print real labels from your real printer and ribbon at the final size. Make the barcode in the generator at its physical size so the test matches production.
  2. Apply them to the real item, using your real process and temperature, and label several of each surface type.
  3. Expose them to the actual conditions, such as a few days in the freezer, a pass through your usual warm-up and condensation cycle, or a stretch outdoors. Include the worst case, like a pallet that moves straight from the freezer to a warm dock.
  4. Scratch, rub and wet them the way handling will. Check for smearing, lifting edges and curling.
  5. Scan every label with your actual scanner, in the place it will really be scanned, then check the results against the not-scanning checklist. If a retailer or customer requires a verification report, see barcode verification grades.

Write down the label, adhesive, ribbon and printer settings of the batch that passed, so a later change in supplier or material can be retested.

Bottom line

Choose thermal transfer on a synthetic facestock for cold, wet or outdoor jobs. Read the adhesive's application temperature and service range separately, apply at room temperature when possible, and let labels set before they change temperature. Then test sample labels on your real items under real conditions and scan them before ordering in bulk. If the labels double as permanent equipment tags, see asset tags with barcodes for numbering and placement.

Sources

  1. Zebra Technologies: Zebra Genuine Supplies Selector Guide (accessed )
  2. Smith Corona Labels: Freezer Label Buying Guide (accessed )
  3. Refrigerated & Frozen Foods: Choosing the Right Pressure-Sensitive Adhesive for Cold Food Packaging Applications (accessed )

Edited by Plain Barcode. Drafted with AI writing tools and checked against the sources listed above.

How guides are researched and corrected: Editorial Policy. Spotted an error? Email hello@plainbarcode.com.

Newsletter

Get an e-mail when Plain Barcode publishes something new

At most one e-mail a day, only about new guides and tools. No tracking pixels. How we handle your address